|
|
|
|
| Page View 1656 |
| Product Information : |
|
|
| Product Name: |
|
Obishi Bench Center โต๊ะวัดศูนย์เพลา |
|
| Product Category: |
|
เครื่องจักร, อุปกรณ์เกี่ยวกับเครื่องจักร, เครื่องมือกล
|
| Product Sub-Category: |
|
Obishi Keiki Seisakusho
|
| Brand: |
|
Bench Center โต๊ะวัดศูนย์เพลา |
| Product Type : |
|
สินค้า, ผลิตภัณฑ์
|
| Short Description : |
|
ศูนย์รวมเครื่องมืออุตสาหกรรม Bench Center - โต๊ะวัดศูนย์เพลา จากญี่ปุ่น โต๊ะวัดศูนย์เพลา - Bench Center Bench center |
| |
|
|
| |
Bench Centers (Standard-Type)
[ Stock No?311 ]
- Used for eccentricity and deflection Measurement of shafts, etc.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*According to your requirement, we can manufacture variations with carbide center or brolly center.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height
Parallelism
(μm) |
Mass
(kg) |
|---|
| SA101 |
No.-1 |
650 |
390 |
150 |
MT-1 |
6 |
33 |
|---|
| SA102 |
No.-2 |
1220 |
820 |
240 |
MT-2 |
8 |
87 |
|---|
| SA103 |
No.-3 |
1645 |
1190 |
300 |
MT-3 |
10 |
135 |
|---|
| SAL101 |
No.1-890L |
890 |
630 |
150 |
MT-1 |
8 |
37 |
|---|
| SAH101 |
No.1-300H |
650 |
400 |
300 |
MT-1 |
10 |
39 |
|---|
Other products of Bench Centers
Bench Centers (P-Type)
[ Stock No?312 ]
- Small sized type of standard model tester.
- Used for eccentricity and deflection Measurement of shafts, etc.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*According to your requirement, we can manufacture variations with carbide center or brolly center.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height
Parallelism
(μm) |
Mass
(kg) |
|---|
| SAP101 |
P-1 |
410 |
150 |
110 |
MT-1 |
5 |
14.0 |
|---|
| SAP102 |
P-2 |
470 |
210 |
15.5 |
|---|
| SAP103 |
P-3 |
560 |
300 |
17.0 |
|---|
Rack Slide Type Bench Centers (ML-Type)
[ Stock No?102 ]
- Dial Gauge Stand can be moved left or right using a rack attched handle.
- Dial Gauge Stand can be moved forward and backward using the handle.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Range
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SML101 |
ML-1 |
680 |
400 |
220 |
Carbide MT-1 |
6 |
43 |
|---|
| SML102 |
ML-2 |
1220 |
800 |
360 |
Carbide MT-2 |
8 |
90 |
|---|
| SML103 |
ML-3 |
1645 |
1180 |
480 |
Carbide MT-3 |
10 |
145 |
|---|
| SML100 |
ML-P |
560 |
300 |
160 |
MT-1 |
5 |
22 |
|---|
Bench Centers (CV-Type)
[ Stock No?313 ]
- Tester with V Block (V Width 16mm) attached to stock.
- Can be used for measurement of shafts, etc with center hole, or without hole
- On the dial gauge stand, a lever type dial gauge is installed.
- Center entry/exit can be performed by a one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SCV101 |
CV-1 |
530 |
300 |
75 |
MT-1 |
5 |
|---|
Vertical/Horizontal Combination Bench Centers (SP-Type)
[ Stock No?309 ]
- Light weight and logical design
- The stock moves by rack gear
- When used vertically, a squareness adjustment method is employed.
- Center entry/exit can be performed by a one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SP101 |
SP-1 |
565 |
270 |
110 |
MT-1 |
8 |
23 |
|---|
| SP102 |
SP-2 |
785 |
500 |
150 |
10 |
43 |
|---|
Universal Bench Center (MV Type)
[ Stock No?401 ]
- Multi purpose type for deflection measurement.
- It is compact with high accuracy.
- Accuracy between center Axis and lower surface, side surface, and edge surfaces is assured.
- Sine bar method that can also measure taper shape.
- Center is common for both male and female.
- Center is straight center, and the center reception part is V groove type.
- The Center can be detached, making it possible for measurement of work pieces with no center hole.
*V Block for stability used during Angle Measurement is supplied.
*Test bar is not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Roller Center Distance
(mm) |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SMV101 |
MV-1 |
300 |
140 |
70 |
200±0.003 |
3 |
|---|
Cast Iron Surface Plate with Center
[ Stock No?307 ]
- Surface Plate Flatness is JIS Grade 1.
- Stock movement part uses V Groove mechanism with T slot.
- V Groove is located in the center of the surface plate width.
- The stock can be detached making it possible to use as a Surface Plate for inspection
*According to your requirement, we can manufacture products with the V Groove located near the edge.
*We can also manufacture special mount (Square pipe material).
*Test bar is not included.
| Code No. |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SE101 |
850×500 |
575 |
150 |
MT-1 |
6 |
215 |
|---|
| SE102 |
1000×500 |
600 |
240 |
MT-2 |
8 |
270 |
|---|
| SE103 |
1000×750 |
390 |
|---|
| SE104 |
1500×500 |
1000 |
300 |
MT-3 |
10 |
500 |
|---|
| SE105 |
1500×1000 |
960 |
|---|
Granite Surface Plate with Center
[ Stock No?339 ]
- Surface Plate is Granite, and Flatness is JIS Grade 1.
- Stock movement part uses V Groove mechanism with T slot. Cast iron material is embedded.
- V Groove is located in the center of the surface plate width
- The stock can be detached making it possible to use as a Surface Plate for inspection
*According to your requirement, we can manufacture products with the V Groove located near the edge
*We can also manufacture special mount (Square pipe material)
*According to your requirement, we can also manufacture special measurement products.
*Test bar is not included.
| Code No. |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SG101 |
1000×750 |
600 |
240 |
MT-2 |
5 |
365 |
|---|
| SG102 |
1500×1000 |
1000 |
300 |
MT-3 |
8 |
960 |
|---|
| SG103 |
2000×1000 |
14500 |
12 |
1570 |
|---|
Granite Vertical-TypeBench Centers (VPG-Type)
[ Stock No?721 ]
- Surface Plate is Granite and Flatness is JISGrade 1
- The Stock moves up/down by gear
- Due to balance weight within the column, it moves with minimum force
*According to your requirement, we can manufacture head spin type
*Test bar is not included.
| Code No. |
Model |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Center Axis Perpendicularity (μm) |
Mass
(kg) |
|---|
| SVP201 |
VPG-1 |
600×500 |
400 |
150 |
Carbide MT-2 |
5 |
195 |
|---|
| SVP202 |
VPG-2 |
900×600 |
700 |
200 |
Carbide MT-3 |
8 |
400 |
|---|
| SVP203 |
VPG-3 |
1000×750 |
1000 |
240 |
12 |
510 |
|---|
| SVP204 |
VPG-1L |
750×500 |
370 |
200 |
Carbide MT-2 |
5 |
300 |
|---|
Vertical-TypeBench Centers (VP-Type)
[ Stock No?720 ]
- Surface Plate flatness is JIS Grade 1.
- Surface Plate is bag type, therefore long term accuracy can be manitained.
- The Stock moves up/down by gear.
- Due to balance weight within the column, it moves with minimum force.
*According to your requirement, we can manufacture head spin type.
*Test bar is not included.
| Code No. |
Model |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Center Axis Perpendicularity (μm) |
Mass
(kg) |
|---|
| SVP101 |
VP-1 |
600×500 |
400 |
150 |
Carbide MT-2 |
5 |
230 |
|---|
| SVP102 |
VP-2 |
900×600 |
700 |
200 |
Carbide MT-3 |
8 |
440 |
|---|
| SVP103 |
VP-3 |
1000×750 |
1000 |
240 |
12 |
550 |
|---|
| SVP104 |
VP-1L |
700×600 |
370 |
200 |
Carbide MT-2 |
5 |
250 |
|---|
Deflection Tester for Gear (SR-Type)
[ Stock No?304 ]
- For gear circle pitch deflection measurement
- Dial Gauge gripping chuck moves up/down due to rack gear.
- The probe easily moves up/down using the lever.
- 7 probes are supplied by default. (Module 1 to 4, 0.5 interval)
*Dial gauge and test bar are not included.
*We can manufacture special measurement probles according to your requirement.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Parallelism
(μm) |
Mass
(kg) |
|---|
| SR101 |
SR-1 |
640 |
300 |
200 |
Carbide MT-2 |
4 |
72 |
|---|
Attachment for Gear Deflection Measurement (SHH Type)
[ Stock No?101 ]
- For gear circle pitch deflection (Deflection) Measurement.
- Install and use with Standard Model tester, Rack Slide Type tester, etc.
- 7 probes are supplied by default. (Every 0.5 from Module 1 to 4)
*Dial Gauge and Deflection Tester are not supplied.
*We can manufacture special measurement probles according to your requirement.
| Code No. | Model | Applicable Deflection Tester | MAX Gear Diameter
(mm) | Probe (7 pcs)
(Module) | Mass
(kg) |
|---|
| SHH100 |
SHH-0 |
P-1,2,3 Type |
130 |
1.0 – 4.0
(0.5 increment) |
4 |
|---|
| SHH101 |
SHH-1 |
NO.-1 Type |
220 |
5 |
|---|
| SHH102 |
SHH-2 |
No.-2 Type |
380 |
10
|
|---|
Attachment for V Support with Rollers (SAR Type)
- Attachment used for measurement when adopting external diameter standard.
- Roller creates a V shape, making it difficult to dent the work piece contact surface.
- Work rotation is easy even for heavy work pieces and so high accuracy measurement can be performed.
- Supported work size φ40~φ100
*Dial Gauge, test bar and deflection tester are not provided. These have to arranged separately.
| Code No. | Model | Applicable Bench
Center | Roller Interval
Parallelism | Roller
Deflection | Mass
(kg) |
|---|
| SAR101 |
SAR-1 |
No.1 ML-1 |
0.01 |
0.003 |
4 |
|---|
| SAR102 |
SAR-2 |
No.2 ML-2 |
0.01 |
0.003 |
7 |
|---|
Attachment for V Support with Height Adjustment (SAV-Type)
- Attachment used for measurement when adopting external diameter standard
- In order for the support part to support various external diameters, the height of the V Support is adjustable on one side
- V Support width is designed to be narrow. It can also support both flangged type of work pieces.
- Supported work size φ8 ~ φ50
- Standard height adjustment range for the adjustable side is ±10
*Dial Gauge, test bar and deflection tester are not provided. These have to arranged separately.
| Code No. | Model | Applicable Bench
Center | Mass
(kg) |
|---|
| SAV101 |
SAV-1 |
No.1 ML-1 |
4 |
|---|
| SAV102 |
SAV-2 |
No.2 ML-2 |
7.5 |
|---|
Arm for Lever Type Dial Gauge (with Micromotion adjustment)?
For deflection testers, a stand that can utilize installation type dial gauge is supplied by default.
By exchanging the arm, it becomes possible to install a lever type dial gauge. Because it comes with a micromotion adjustment knob, dial gauge setting is easy.
*System installation hole is φ6mm (Dial Gauge is not included.)
| Code No. |
Applicable Bench
Center Model |
|---|
| SS101 |
No.1, ML-1 |
|---|
| SS102 |
No.2, ML-2 |
|---|
| SS103 |
No.3, ML-3 |
|---|
| SS104 |
P-1, P-2, P-3 |
|---|
Bench Centers (Standard-Type)
[ Stock No?311 ]
- Used for eccentricity and deflection Measurement of shafts, etc.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*According to your requirement, we can manufacture variations with carbide center or brolly center.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height
Parallelism
(μm) |
Mass
(kg) |
|---|
| SA101 |
No.-1 |
650 |
390 |
150 |
MT-1 |
6 |
33 |
|---|
| SA102 |
No.-2 |
1220 |
820 |
240 |
MT-2 |
8 |
87 |
|---|
| SA103 |
No.-3 |
1645 |
1190 |
300 |
MT-3 |
10 |
135 |
|---|
| SAL101 |
No.1-890L |
890 |
630 |
150 |
MT-1 |
8 |
37 |
|---|
| SAH101 |
No.1-300H |
650 |
400 |
300 |
MT-1 |
10 |
39 |
|---|
Other products of Bench Centers
Bench Centers (P-Type)
[ Stock No?312 ]
- Small sized type of standard model tester.
- Used for eccentricity and deflection Measurement of shafts, etc.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*According to your requirement, we can manufacture variations with carbide center or brolly center.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height
Parallelism
(μm) |
Mass
(kg) |
|---|
| SAP101 |
P-1 |
410 |
150 |
110 |
MT-1 |
5 |
14.0 |
|---|
| SAP102 |
P-2 |
470 |
210 |
15.5 |
|---|
| SAP103 |
P-3 |
560 |
300 |
17.0 |
|---|
Rack Slide Type Bench Centers (ML-Type)
[ Stock No?102 ]
- Dial Gauge Stand can be moved left or right using a rack attched handle.
- Dial Gauge Stand can be moved forward and backward using the handle.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Range
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SML101 |
ML-1 |
680 |
400 |
220 |
Carbide MT-1 |
6 |
43 |
|---|
| SML102 |
ML-2 |
1220 |
800 |
360 |
Carbide MT-2 |
8 |
90 |
|---|
| SML103 |
ML-3 |
1645 |
1180 |
480 |
Carbide MT-3 |
10 |
145 |
|---|
| SML100 |
ML-P |
560 |
300 |
160 |
MT-1 |
5 |
22 |
|---|
Bench Centers (CV-Type)
[ Stock No?313 ]
- Tester with V Block (V Width 16mm) attached to stock.
- Can be used for measurement of shafts, etc with center hole, or without hole
- On the dial gauge stand, a lever type dial gauge is installed.
- Center entry/exit can be performed by a one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SCV101 |
CV-1 |
530 |
300 |
75 |
MT-1 |
5 |
|---|
Vertical/Horizontal Combination Bench Centers (SP-Type)
[ Stock No?309 ]
- Light weight and logical design
- The stock moves by rack gear
- When used vertically, a squareness adjustment method is employed.
- Center entry/exit can be performed by a one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SP101 |
SP-1 |
565 |
270 |
110 |
MT-1 |
8 |
23 |
|---|
| SP102 |
SP-2 |
785 |
500 |
150 |
10 |
43 |
|---|
Universal Bench Center (MV Type)
[ Stock No?401 ]
- Multi purpose type for deflection measurement.
- It is compact with high accuracy.
- Accuracy between center Axis and lower surface, side surface, and edge surfaces is assured.
- Sine bar method that can also measure taper shape.
- Center is common for both male and female.
- Center is straight center, and the center reception part is V groove type.
- The Center can be detached, making it possible for measurement of work pieces with no center hole.
*V Block for stability used during Angle Measurement is supplied.
*Test bar is not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Roller Center Distance
(mm) |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SMV101 |
MV-1 |
300 |
140 |
70 |
200±0.003 |
3 |
|---|
Cast Iron Surface Plate with Center
[ Stock No?307 ]
- Surface Plate Flatness is JIS Grade 1.
- Stock movement part uses V Groove mechanism with T slot.
- V Groove is located in the center of the surface plate width.
- The stock can be detached making it possible to use as a Surface Plate for inspection
*According to your requirement, we can manufacture products with the V Groove located near the edge.
*We can also manufacture special mount (Square pipe material).
*Test bar is not included.
| Code No. |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SE101 |
850×500 |
575 |
150 |
MT-1 |
6 |
215 |
|---|
| SE102 |
1000×500 |
600 |
240 |
MT-2 |
8 |
270 |
|---|
| SE103 |
1000×750 |
390 |
|---|
| SE104 |
1500×500 |
1000 |
300 |
MT-3 |
10 |
500 |
|---|
| SE105 |
1500×1000 |
960 |
|---|
Granite Surface Plate with Center
[ Stock No?339 ]
- Surface Plate is Granite, and Flatness is JIS Grade 1.
- Stock movement part uses V Groove mechanism with T slot. Cast iron material is embedded.
- V Groove is located in the center of the surface plate width
- The stock can be detached making it possible to use as a Surface Plate for inspection
*According to your requirement, we can manufacture products with the V Groove located near the edge
*We can also manufacture special mount (Square pipe material)
*According to your requirement, we can also manufacture special measurement products.
*Test bar is not included.
| Code No. |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SG101 |
1000×750 |
600 |
240 |
MT-2 |
5 |
365 |
|---|
| SG102 |
1500×1000 |
1000 |
300 |
MT-3 |
8 |
960 |
|---|
| SG103 |
2000×1000 |
14500 |
12 |
1570 |
|---|
Granite Vertical-TypeBench Centers (VPG-Type)
[ Stock No?721 ]
- Surface Plate is Granite and Flatness is JISGrade 1
- The Stock moves up/down by gear
- Due to balance weight within the column, it moves with minimum force
*According to your requirement, we can manufacture head spin type
*Test bar is not included.
| Code No. |
Model |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Center Axis Perpendicularity (μm) |
Mass
(kg) |
|---|
| SVP201 |
VPG-1 |
600×500 |
400 |
150 |
Carbide MT-2 |
5 |
195 |
|---|
| SVP202 |
VPG-2 |
900×600 |
700 |
200 |
Carbide MT-3 |
8 |
400 |
|---|
| SVP203 |
VPG-3 |
1000×750 |
1000 |
240 |
12 |
510 |
|---|
| SVP204 |
VPG-1L |
750×500 |
370 |
200 |
Carbide MT-2 |
5 |
300 |
|---|
Vertical-TypeBench Centers (VP-Type)
[ Stock No?720 ]
- Surface Plate flatness is JIS Grade 1.
- Surface Plate is bag type, therefore long term accuracy can be manitained.
- The Stock moves up/down by gear.
- Due to balance weight within the column, it moves with minimum force.
*According to your requirement, we can manufacture head spin type.
*Test bar is not included.
| Code No. |
Model |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Center Axis Perpendicularity (μm) |
Mass
(kg) |
|---|
| SVP101 |
VP-1 |
600×500 |
400 |
150 |
Carbide MT-2 |
5 |
230 |
|---|
| SVP102 |
VP-2 |
900×600 |
700 |
200 |
Carbide MT-3 |
8 |
440 |
|---|
| SVP103 |
VP-3 |
1000×750 |
1000 |
240 |
12 |
550 |
|---|
| SVP104 |
VP-1L |
700×600 |
370 |
200 |
Carbide MT-2 |
5 |
250 |
|---|
Deflection Tester for Gear (SR-Type)
[ Stock No?304 ]
- For gear circle pitch deflection measurement
- Dial Gauge gripping chuck moves up/down due to rack gear.
- The probe easily moves up/down using the lever.
- 7 probes are supplied by default. (Module 1 to 4, 0.5 interval)
*Dial gauge and test bar are not included.
*We can manufacture special measurement probles according to your requirement.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Parallelism
(μm) |
Mass
(kg) |
|---|
| SR101 |
SR-1 |
640 |
300 |
200 |
Carbide MT-2 |
4 |
72 |
|---|
Attachment for Gear Deflection Measurement (SHH Type)
[ Stock No?101 ]
- For gear circle pitch deflection (Deflection) Measurement.
- Install and use with Standard Model tester, Rack Slide Type tester, etc.
- 7 probes are supplied by default. (Every 0.5 from Module 1 to 4)
*Dial Gauge and Deflection Tester are not supplied.
*We can manufacture special measurement probles according to your requirement.
| Code No. | Model | Applicable Deflection Tester | MAX Gear Diameter
(mm) | Probe (7 pcs)
(Module) | Mass
(kg) |
|---|
| SHH100 |
SHH-0 |
P-1,2,3 Type |
130 |
1.0 – 4.0
(0.5 increment) |
4 |
|---|
| SHH101 |
SHH-1 |
NO.-1 Type |
220 |
5 |
|---|
| SHH102 |
SHH-2 |
No.-2 Type |
380 |
10
|
|---|
Attachment for V Support with Rollers (SAR Type)
- Attachment used for measurement when adopting external diameter standard.
- Roller creates a V shape, making it difficult to dent the work piece contact surface.
- Work rotation is easy even for heavy work pieces and so high accuracy measurement can be performed.
- Supported work size φ40~φ100
*Dial Gauge, test bar and deflection tester are not provided. These have to arranged separately.
| Code No. | Model | Applicable Bench
Center | Roller Interval
Parallelism | Roller
Deflection | Mass
(kg) |
|---|
| SAR101 |
SAR-1 |
No.1 ML-1 |
0.01 |
0.003 |
4 |
|---|
| SAR102 |
SAR-2 |
No.2 ML-2 |
0.01 |
0.003 |
7 |
|---|
Attachment for V Support with Height Adjustment (SAV-Type)
- Attachment used for measurement when adopting external diameter standard
- In order for the support part to support various external diameters, the height of the V Support is adjustable on one side
- V Support width is designed to be narrow. It can also support both flangged type of work pieces.
- Supported work size φ8 ~ φ50
- Standard height adjustment range for the adjustable side is ±10
*Dial Gauge, test bar and deflection tester are not provided. These have to arranged separately.
| Code No. | Model | Applicable Bench
Center | Mass
(kg) |
|---|
| SAV101 |
SAV-1 |
No.1 ML-1 |
4 |
|---|
| SAV102 |
SAV-2 |
No.2 ML-2 |
7.5 |
|---|
Arm for Lever Type Dial Gauge (with Micromotion adjustment)?
For deflection testers, a stand that can utilize installation type dial gauge is supplied by default.
By exchanging the arm, it becomes possible to install a lever type dial gauge. Because it comes with a micromotion adjustment knob, dial gauge setting is easy.
*System installation hole is φ6mm (Dial Gauge is not included.)
| Code No. |
Applicable Bench
Center Model |
|---|
| SS101 |
No.1, ML-1 |
|---|
| SS102 |
No.2, ML-2 |
|---|
| SS103 |
No.3, ML-3 |
|---|
| SS104 |
P-1, P-2, P-3 |
|---|
Bench Centers (Standard-Type)
[ Stock No?311 ]
- Used for eccentricity and deflection Measurement of shafts, etc.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*According to your requirement, we can manufacture variations with carbide center or brolly center.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height
Parallelism
(μm) |
Mass
(kg) |
|---|
| SA101 |
No.-1 |
650 |
390 |
150 |
MT-1 |
6 |
33 |
|---|
| SA102 |
No.-2 |
1220 |
820 |
240 |
MT-2 |
8 |
87 |
|---|
| SA103 |
No.-3 |
1645 |
1190 |
300 |
MT-3 |
10 |
135 |
|---|
| SAL101 |
No.1-890L |
890 |
630 |
150 |
MT-1 |
8 |
37 |
|---|
| SAH101 |
No.1-300H |
650 |
400 |
300 |
MT-1 |
10 |
39 |
|---|
Other products of Bench Centers
Bench Centers (P-Type)
[ Stock No?312 ]
- Small sized type of standard model tester.
- Used for eccentricity and deflection Measurement of shafts, etc.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*According to your requirement, we can manufacture variations with carbide center or brolly center.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height
Parallelism
(μm) |
Mass
(kg) |
|---|
| SAP101 |
P-1 |
410 |
150 |
110 |
MT-1 |
5 |
14.0 |
|---|
| SAP102 |
P-2 |
470 |
210 |
15.5 |
|---|
| SAP103 |
P-3 |
560 |
300 |
17.0 |
|---|
Rack Slide Type Bench Centers (ML-Type)
[ Stock No?102 ]
- Dial Gauge Stand can be moved left or right using a rack attched handle.
- Dial Gauge Stand can be moved forward and backward using the handle.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Range
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SML101 |
ML-1 |
680 |
400 |
220 |
Carbide MT-1 |
6 |
43 |
|---|
| SML102 |
ML-2 |
1220 |
800 |
360 |
Carbide MT-2 |
8 |
90 |
|---|
| SML103 |
ML-3 |
1645 |
1180 |
480 |
Carbide MT-3 |
10 |
145 |
|---|
| SML100 |
ML-P |
560 |
300 |
160 |
MT-1 |
5 |
22 |
|---|
Bench Centers (CV-Type)
[ Stock No?313 ]
- Tester with V Block (V Width 16mm) attached to stock.
- Can be used for measurement of shafts, etc with center hole, or without hole
- On the dial gauge stand, a lever type dial gauge is installed.
- Center entry/exit can be performed by a one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SCV101 |
CV-1 |
530 |
300 |
75 |
MT-1 |
5 |
|---|
Vertical/Horizontal Combination Bench Centers (SP-Type)
[ Stock No?309 ]
- Light weight and logical design
- The stock moves by rack gear
- When used vertically, a squareness adjustment method is employed.
- Center entry/exit can be performed by a one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SP101 |
SP-1 |
565 |
270 |
110 |
MT-1 |
8 |
23 |
|---|
| SP102 |
SP-2 |
785 |
500 |
150 |
10 |
43 |
|---|
Universal Bench Center (MV Type)
[ Stock No?401 ]
- Multi purpose type for deflection measurement.
- It is compact with high accuracy.
- Accuracy between center Axis and lower surface, side surface, and edge surfaces is assured.
- Sine bar method that can also measure taper shape.
- Center is common for both male and female.
- Center is straight center, and the center reception part is V groove type.
- The Center can be detached, making it possible for measurement of work pieces with no center hole.
*V Block for stability used during Angle Measurement is supplied.
*Test bar is not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Roller Center Distance
(mm) |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SMV101 |
MV-1 |
300 |
140 |
70 |
200±0.003 |
3 |
|---|
Cast Iron Surface Plate with Center
[ Stock No?307 ]
- Surface Plate Flatness is JIS Grade 1.
- Stock movement part uses V Groove mechanism with T slot.
- V Groove is located in the center of the surface plate width.
- The stock can be detached making it possible to use as a Surface Plate for inspection
*According to your requirement, we can manufacture products with the V Groove located near the edge.
*We can also manufacture special mount (Square pipe material).
*Test bar is not included.
| Code No. |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SE101 |
850×500 |
575 |
150 |
MT-1 |
6 |
215 |
|---|
| SE102 |
1000×500 |
600 |
240 |
MT-2 |
8 |
270 |
|---|
| SE103 |
1000×750 |
390 |
|---|
| SE104 |
1500×500 |
1000 |
300 |
MT-3 |
10 |
500 |
|---|
| SE105 |
1500×1000 |
960 |
|---|
Granite Surface Plate with Center
[ Stock No?339 ]
- Surface Plate is Granite, and Flatness is JIS Grade 1.
- Stock movement part uses V Groove mechanism with T slot. Cast iron material is embedded.
- V Groove is located in the center of the surface plate width
- The stock can be detached making it possible to use as a Surface Plate for inspection
*According to your requirement, we can manufacture products with the V Groove located near the edge
*We can also manufacture special mount (Square pipe material)
*According to your requirement, we can also manufacture special measurement products.
*Test bar is not included.
| Code No. |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SG101 |
1000×750 |
600 |
240 |
MT-2 |
5 |
365 |
|---|
| SG102 |
1500×1000 |
1000 |
300 |
MT-3 |
8 |
960 |
|---|
| SG103 |
2000×1000 |
14500 |
12 |
1570 |
|---|
Granite Vertical-TypeBench Centers (VPG-Type)
[ Stock No?721 ]
- Surface Plate is Granite and Flatness is JISGrade 1
- The Stock moves up/down by gear
- Due to balance weight within the column, it moves with minimum force
*According to your requirement, we can manufacture head spin type
*Test bar is not included.
| Code No. |
Model |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Center Axis Perpendicularity (μm) |
Mass
(kg) |
|---|
| SVP201 |
VPG-1 |
600×500 |
400 |
150 |
Carbide MT-2 |
5 |
195 |
|---|
| SVP202 |
VPG-2 |
900×600 |
700 |
200 |
Carbide MT-3 |
8 |
400 |
|---|
| SVP203 |
VPG-3 |
1000×750 |
1000 |
240 |
12 |
510 |
|---|
| SVP204 |
VPG-1L |
750×500 |
370 |
200 |
Carbide MT-2 |
5 |
300 |
|---|
Vertical-TypeBench Centers (VP-Type)
[ Stock No?720 ]
- Surface Plate flatness is JIS Grade 1.
- Surface Plate is bag type, therefore long term accuracy can be manitained.
- The Stock moves up/down by gear.
- Due to balance weight within the column, it moves with minimum force.
*According to your requirement, we can manufacture head spin type.
*Test bar is not included.
| Code No. |
Model |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Center Axis Perpendicularity (μm) |
Mass
(kg) |
|---|
| SVP101 |
VP-1 |
600×500 |
400 |
150 |
Carbide MT-2 |
5 |
230 |
|---|
| SVP102 |
VP-2 |
900×600 |
700 |
200 |
Carbide MT-3 |
8 |
440 |
|---|
| SVP103 |
VP-3 |
1000×750 |
1000 |
240 |
12 |
550 |
|---|
| SVP104 |
VP-1L |
700×600 |
370 |
200 |
Carbide MT-2 |
5 |
250 |
|---|
Deflection Tester for Gear (SR-Type)
[ Stock No?304 ]
- For gear circle pitch deflection measurement
- Dial Gauge gripping chuck moves up/down due to rack gear.
- The probe easily moves up/down using the lever.
- 7 probes are supplied by default. (Module 1 to 4, 0.5 interval)
*Dial gauge and test bar are not included.
*We can manufacture special measurement probles according to your requirement.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Parallelism
(μm) |
Mass
(kg) |
|---|
| SR101 |
SR-1 |
640 |
300 |
200 |
Carbide MT-2 |
4 |
72 |
|---|
Attachment for Gear Deflection Measurement (SHH Type)
[ Stock No?101 ]
- For gear circle pitch deflection (Deflection) Measurement.
- Install and use with Standard Model tester, Rack Slide Type tester, etc.
- 7 probes are supplied by default. (Every 0.5 from Module 1 to 4)
*Dial Gauge and Deflection Tester are not supplied.
*We can manufacture special measurement probles according to your requirement.
| Code No. | Model | Applicable Deflection Tester | MAX Gear Diameter
(mm) | Probe (7 pcs)
(Module) | Mass
(kg) |
|---|
| SHH100 |
SHH-0 |
P-1,2,3 Type |
130 |
1.0 – 4.0
(0.5 increment) |
4 |
|---|
| SHH101 |
SHH-1 |
NO.-1 Type |
220 |
5 |
|---|
| SHH102 |
SHH-2 |
No.-2 Type |
380 |
10
|
|---|
Attachment for V Support with Rollers (SAR Type)
- Attachment used for measurement when adopting external diameter standard.
- Roller creates a V shape, making it difficult to dent the work piece contact surface.
- Work rotation is easy even for heavy work pieces and so high accuracy measurement can be performed.
- Supported work size φ40~φ100
*Dial Gauge, test bar and deflection tester are not provided. These have to arranged separately.
| Code No. | Model | Applicable Bench
Center | Roller Interval
Parallelism | Roller
Deflection | Mass
(kg) |
|---|
| SAR101 |
SAR-1 |
No.1 ML-1 |
0.01 |
0.003 |
4 |
|---|
| SAR102 |
SAR-2 |
No.2 ML-2 |
0.01 |
0.003 |
7 |
|---|
Attachment for V Support with Height Adjustment (SAV-Type)
- Attachment used for measurement when adopting external diameter standard
- In order for the support part to support various external diameters, the height of the V Support is adjustable on one side
- V Support width is designed to be narrow. It can also support both flangged type of work pieces.
- Supported work size φ8 ~ φ50
- Standard height adjustment range for the adjustable side is ±10
*Dial Gauge, test bar and deflection tester are not provided. These have to arranged separately.
| Code No. | Model | Applicable Bench
Center | Mass
(kg) |
|---|
| SAV101 |
SAV-1 |
No.1 ML-1 |
4 |
|---|
| SAV102 |
SAV-2 |
No.2 ML-2 |
7.5 |
|---|
Arm for Lever Type Dial Gauge (with Micromotion adjustment)?
For deflection testers, a stand that can utilize installation type dial gauge is supplied by default.
By exchanging the arm, it becomes possible to install a lever type dial gauge. Because it comes with a micromotion adjustment knob, dial gauge setting is easy.
*System installation hole is φ6mm (Dial Gauge is not included.)
| Code No. |
Applicable Bench
Center Model |
|---|
| SS101 |
No.1, ML-1 |
|---|
| SS102 |
No.2, ML-2 |
|---|
| SS103 |
No.3, ML-3 |
|---|
| SS104 |
P-1, P-2, P-3 |
|---|
Bench Centers (Standard-Type)
[ Stock No?311 ]
- Used for eccentricity and deflection Measurement of shafts, etc.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*According to your requirement, we can manufacture variations with carbide center or brolly center.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height
Parallelism
(μm) |
Mass
(kg) |
|---|
| SA101 |
No.-1 |
650 |
390 |
150 |
MT-1 |
6 |
33 |
|---|
| SA102 |
No.-2 |
1220 |
820 |
240 |
MT-2 |
8 |
87 |
|---|
| SA103 |
No.-3 |
1645 |
1190 |
300 |
MT-3 |
10 |
135 |
|---|
| SAL101 |
No.1-890L |
890 |
630 |
150 |
MT-1 |
8 |
37 |
|---|
| SAH101 |
No.1-300H |
650 |
400 |
300 |
MT-1 |
10 |
39 |
|---|
Other products of Bench Centers
Bench Centers (P-Type)
[ Stock No?312 ]
- Small sized type of standard model tester.
- Used for eccentricity and deflection Measurement of shafts, etc.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*According to your requirement, we can manufacture variations with carbide center or brolly center.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height
Parallelism
(μm) |
Mass
(kg) |
|---|
| SAP101 |
P-1 |
410 |
150 |
110 |
MT-1 |
5 |
14.0 |
|---|
| SAP102 |
P-2 |
470 |
210 |
15.5 |
|---|
| SAP103 |
P-3 |
560 |
300 |
17.0 |
|---|
Rack Slide Type Bench Centers (ML-Type)
[ Stock No?102 ]
- Dial Gauge Stand can be moved left or right using a rack attched handle.
- Dial Gauge Stand can be moved forward and backward using the handle.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Range
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SML101 |
ML-1 |
680 |
400 |
220 |
Carbide MT-1 |
6 |
43 |
|---|
| SML102 |
ML-2 |
1220 |
800 |
360 |
Carbide MT-2 |
8 |
90 |
|---|
| SML103 |
ML-3 |
1645 |
1180 |
480 |
Carbide MT-3 |
10 |
145 |
|---|
| SML100 |
ML-P |
560 |
300 |
160 |
MT-1 |
5 |
22 |
|---|
Bench Centers (CV-Type)
[ Stock No?313 ]
- Tester with V Block (V Width 16mm) attached to stock.
- Can be used for measurement of shafts, etc with center hole, or without hole
- On the dial gauge stand, a lever type dial gauge is installed.
- Center entry/exit can be performed by a one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SCV101 |
CV-1 |
530 |
300 |
75 |
MT-1 |
5 |
|---|
Vertical/Horizontal Combination Bench Centers (SP-Type)
[ Stock No?309 ]
- Light weight and logical design
- The stock moves by rack gear
- When used vertically, a squareness adjustment method is employed.
- Center entry/exit can be performed by a one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SP101 |
SP-1 |
565 |
270 |
110 |
MT-1 |
8 |
23 |
|---|
| SP102 |
SP-2 |
785 |
500 |
150 |
10 |
43 |
|---|
Universal Bench Center (MV Type)
[ Stock No?401 ]
- Multi purpose type for deflection measurement.
- It is compact with high accuracy.
- Accuracy between center Axis and lower surface, side surface, and edge surfaces is assured.
- Sine bar method that can also measure taper shape.
- Center is common for both male and female.
- Center is straight center, and the center reception part is V groove type.
- The Center can be detached, making it possible for measurement of work pieces with no center hole.
*V Block for stability used during Angle Measurement is supplied.
*Test bar is not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Roller Center Distance
(mm) |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SMV101 |
MV-1 |
300 |
140 |
70 |
200±0.003 |
3 |
|---|
Cast Iron Surface Plate with Center
[ Stock No?307 ]
- Surface Plate Flatness is JIS Grade 1.
- Stock movement part uses V Groove mechanism with T slot.
- V Groove is located in the center of the surface plate width.
- The stock can be detached making it possible to use as a Surface Plate for inspection
*According to your requirement, we can manufacture products with the V Groove located near the edge.
*We can also manufacture special mount (Square pipe material).
*Test bar is not included.
| Code No. |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SE101 |
850×500 |
575 |
150 |
MT-1 |
6 |
215 |
|---|
| SE102 |
1000×500 |
600 |
240 |
MT-2 |
8 |
270 |
|---|
| SE103 |
1000×750 |
390 |
|---|
| SE104 |
1500×500 |
1000 |
300 |
MT-3 |
10 |
500 |
|---|
| SE105 |
1500×1000 |
960 |
|---|
Granite Surface Plate with Center
[ Stock No?339 ]
- Surface Plate is Granite, and Flatness is JIS Grade 1.
- Stock movement part uses V Groove mechanism with T slot. Cast iron material is embedded.
- V Groove is located in the center of the surface plate width
- The stock can be detached making it possible to use as a Surface Plate for inspection
*According to your requirement, we can manufacture products with the V Groove located near the edge
*We can also manufacture special mount (Square pipe material)
*According to your requirement, we can also manufacture special measurement products.
*Test bar is not included.
| Code No. |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SG101 |
1000×750 |
600 |
240 |
MT-2 |
5 |
365 |
|---|
| SG102 |
1500×1000 |
1000 |
300 |
MT-3 |
8 |
960 |
|---|
| SG103 |
2000×1000 |
14500 |
12 |
1570 |
|---|
Granite Vertical-TypeBench Centers (VPG-Type)
[ Stock No?721 ]
- Surface Plate is Granite and Flatness is JISGrade 1
- The Stock moves up/down by gear
- Due to balance weight within the column, it moves with minimum force
*According to your requirement, we can manufacture head spin type
*Test bar is not included.
| Code No. |
Model |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Center Axis Perpendicularity (μm) |
Mass
(kg) |
|---|
| SVP201 |
VPG-1 |
600×500 |
400 |
150 |
Carbide MT-2 |
5 |
195 |
|---|
| SVP202 |
VPG-2 |
900×600 |
700 |
200 |
Carbide MT-3 |
8 |
400 |
|---|
| SVP203 |
VPG-3 |
1000×750 |
1000 |
240 |
12 |
510 |
|---|
| SVP204 |
VPG-1L |
750×500 |
370 |
200 |
Carbide MT-2 |
5 |
300 |
|---|
Vertical-TypeBench Centers (VP-Type)
[ Stock No?720 ]
- Surface Plate flatness is JIS Grade 1.
- Surface Plate is bag type, therefore long term accuracy can be manitained.
- The Stock moves up/down by gear.
- Due to balance weight within the column, it moves with minimum force.
*According to your requirement, we can manufacture head spin type.
*Test bar is not included.
| Code No. |
Model |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Center Axis Perpendicularity (μm) |
Mass
(kg) |
|---|
| SVP101 |
VP-1 |
600×500 |
400 |
150 |
Carbide MT-2 |
5 |
230 |
|---|
| SVP102 |
VP-2 |
900×600 |
700 |
200 |
Carbide MT-3 |
8 |
440 |
|---|
| SVP103 |
VP-3 |
1000×750 |
1000 |
240 |
12 |
550 |
|---|
| SVP104 |
VP-1L |
700×600 |
370 |
200 |
Carbide MT-2 |
5 |
250 |
|---|
Deflection Tester for Gear (SR-Type)
[ Stock No?304 ]
- For gear circle pitch deflection measurement
- Dial Gauge gripping chuck moves up/down due to rack gear.
- The probe easily moves up/down using the lever.
- 7 probes are supplied by default. (Module 1 to 4, 0.5 interval)
*Dial gauge and test bar are not included.
*We can manufacture special measurement probles according to your requirement.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Parallelism
(μm) |
Mass
(kg) |
|---|
| SR101 |
SR-1 |
640 |
300 |
200 |
Carbide MT-2 |
4 |
72 |
|---|
Attachment for Gear Deflection Measurement (SHH Type)
[ Stock No?101 ]
- For gear circle pitch deflection (Deflection) Measurement.
- Install and use with Standard Model tester, Rack Slide Type tester, etc.
- 7 probes are supplied by default. (Every 0.5 from Module 1 to 4)
*Dial Gauge and Deflection Tester are not supplied.
*We can manufacture special measurement probles according to your requirement.
| Code No. | Model | Applicable Deflection Tester | MAX Gear Diameter
(mm) | Probe (7 pcs)
(Module) | Mass
(kg) |
|---|
| SHH100 |
SHH-0 |
P-1,2,3 Type |
130 |
1.0 – 4.0
(0.5 increment) |
4 |
|---|
| SHH101 |
SHH-1 |
NO.-1 Type |
220 |
5 |
|---|
| SHH102 |
SHH-2 |
No.-2 Type |
380 |
10
|
|---|
Attachment for V Support with Rollers (SAR Type)
- Attachment used for measurement when adopting external diameter standard.
- Roller creates a V shape, making it difficult to dent the work piece contact surface.
- Work rotation is easy even for heavy work pieces and so high accuracy measurement can be performed.
- Supported work size φ40~φ100
*Dial Gauge, test bar and deflection tester are not provided. These have to arranged separately.
| Code No. | Model | Applicable Bench
Center | Roller Interval
Parallelism | Roller
Deflection | Mass
(kg) |
|---|
| SAR101 |
SAR-1 |
No.1 ML-1 |
0.01 |
0.003 |
4 |
|---|
| SAR102 |
SAR-2 |
No.2 ML-2 |
0.01 |
0.003 |
7 |
|---|
Attachment for V Support with Height Adjustment (SAV-Type)
- Attachment used for measurement when adopting external diameter standard
- In order for the support part to support various external diameters, the height of the V Support is adjustable on one side
- V Support width is designed to be narrow. It can also support both flangged type of work pieces.
- Supported work size φ8 ~ φ50
- Standard height adjustment range for the adjustable side is ±10
*Dial Gauge, test bar and deflection tester are not provided. These have to arranged separately.
| Code No. | Model | Applicable Bench
Center | Mass
(kg) |
|---|
| SAV101 |
SAV-1 |
No.1 ML-1 |
4 |
|---|
| SAV102 |
SAV-2 |
No.2 ML-2 |
7.5 |
|---|
Arm for Lever Type Dial Gauge (with Micromotion adjustment)?
For deflection testers, a stand that can utilize installation type dial gauge is supplied by default.
By exchanging the arm, it becomes possible to install a lever type dial gauge. Because it comes with a micromotion adjustment knob, dial gauge setting is easy.
*System installation hole is φ6mm (Dial Gauge is not included.)
| Code No. |
Applicable Bench
Center Model |
|---|
| SS101 |
No.1, ML-1 |
|---|
| SS102 |
No.2, ML-2 |
|---|
| SS103 |
No.3, ML-3 |
|---|
| SS104 |
P-1, P-2, P-3 |
|---|
Bench Centers (Standard-Type)
[ Stock No?311 ]
- Used for eccentricity and deflection Measurement of shafts, etc.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*According to your requirement, we can manufacture variations with carbide center or brolly center.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height
Parallelism
(μm) |
Mass
(kg) |
|---|
| SA101 |
No.-1 |
650 |
390 |
150 |
MT-1 |
6 |
33 |
|---|
| SA102 |
No.-2 |
1220 |
820 |
240 |
MT-2 |
8 |
87 |
|---|
| SA103 |
No.-3 |
1645 |
1190 |
300 |
MT-3 |
10 |
135 |
|---|
| SAL101 |
No.1-890L |
890 |
630 |
150 |
MT-1 |
8 |
37 |
|---|
| SAH101 |
No.1-300H |
650 |
400 |
300 |
MT-1 |
10 |
39 |
|---|
Other products of Bench Centers
Bench Centers (P-Type)
[ Stock No?312 ]
- Small sized type of standard model tester.
- Used for eccentricity and deflection Measurement of shafts, etc.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*According to your requirement, we can manufacture variations with carbide center or brolly center.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height
Parallelism
(μm) |
Mass
(kg) |
|---|
| SAP101 |
P-1 |
410 |
150 |
110 |
MT-1 |
5 |
14.0 |
|---|
| SAP102 |
P-2 |
470 |
210 |
15.5 |
|---|
| SAP103 |
P-3 |
560 |
300 |
17.0 |
|---|
Rack Slide Type Bench Centers (ML-Type)
[ Stock No?102 ]
- Dial Gauge Stand can be moved left or right using a rack attched handle.
- Dial Gauge Stand can be moved forward and backward using the handle.
- Parallelism between table upper surface and center is assured.
- Center entry/exit is performed by one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Range
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SML101 |
ML-1 |
680 |
400 |
220 |
Carbide MT-1 |
6 |
43 |
|---|
| SML102 |
ML-2 |
1220 |
800 |
360 |
Carbide MT-2 |
8 |
90 |
|---|
| SML103 |
ML-3 |
1645 |
1180 |
480 |
Carbide MT-3 |
10 |
145 |
|---|
| SML100 |
ML-P |
560 |
300 |
160 |
MT-1 |
5 |
22 |
|---|
Bench Centers (CV-Type)
[ Stock No?313 ]
- Tester with V Block (V Width 16mm) attached to stock.
- Can be used for measurement of shafts, etc with center hole, or without hole
- On the dial gauge stand, a lever type dial gauge is installed.
- Center entry/exit can be performed by a one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SCV101 |
CV-1 |
530 |
300 |
75 |
MT-1 |
5 |
|---|
Vertical/Horizontal Combination Bench Centers (SP-Type)
[ Stock No?309 ]
- Light weight and logical design
- The stock moves by rack gear
- When used vertically, a squareness adjustment method is employed.
- Center entry/exit can be performed by a one touch lever.
*Dial gauge and test bar are not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SP101 |
SP-1 |
565 |
270 |
110 |
MT-1 |
8 |
23 |
|---|
| SP102 |
SP-2 |
785 |
500 |
150 |
10 |
43 |
|---|
Universal Bench Center (MV Type)
[ Stock No?401 ]
- Multi purpose type for deflection measurement.
- It is compact with high accuracy.
- Accuracy between center Axis and lower surface, side surface, and edge surfaces is assured.
- Sine bar method that can also measure taper shape.
- Center is common for both male and female.
- Center is straight center, and the center reception part is V groove type.
- The Center can be detached, making it possible for measurement of work pieces with no center hole.
*V Block for stability used during Angle Measurement is supplied.
*Test bar is not included.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Center Height
(mm) |
Roller Center Distance
(mm) |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SMV101 |
MV-1 |
300 |
140 |
70 |
200±0.003 |
3 |
|---|
Cast Iron Surface Plate with Center
[ Stock No?307 ]
- Surface Plate Flatness is JIS Grade 1.
- Stock movement part uses V Groove mechanism with T slot.
- V Groove is located in the center of the surface plate width.
- The stock can be detached making it possible to use as a Surface Plate for inspection
*According to your requirement, we can manufacture products with the V Groove located near the edge.
*We can also manufacture special mount (Square pipe material).
*Test bar is not included.
| Code No. |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SE101 |
850×500 |
575 |
150 |
MT-1 |
6 |
215 |
|---|
| SE102 |
1000×500 |
600 |
240 |
MT-2 |
8 |
270 |
|---|
| SE103 |
1000×750 |
390 |
|---|
| SE104 |
1500×500 |
1000 |
300 |
MT-3 |
10 |
500 |
|---|
| SE105 |
1500×1000 |
960 |
|---|
Granite Surface Plate with Center
[ Stock No?339 ]
- Surface Plate is Granite, and Flatness is JIS Grade 1.
- Stock movement part uses V Groove mechanism with T slot. Cast iron material is embedded.
- V Groove is located in the center of the surface plate width
- The stock can be detached making it possible to use as a Surface Plate for inspection
*According to your requirement, we can manufacture products with the V Groove located near the edge
*We can also manufacture special mount (Square pipe material)
*According to your requirement, we can also manufacture special measurement products.
*Test bar is not included.
| Code No. |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Height Parallelism
(μm) |
Mass
(kg) |
|---|
| SG101 |
1000×750 |
600 |
240 |
MT-2 |
5 |
365 |
|---|
| SG102 |
1500×1000 |
1000 |
300 |
MT-3 |
8 |
960 |
|---|
| SG103 |
2000×1000 |
14500 |
12 |
1570 |
|---|
Granite Vertical-TypeBench Centers (VPG-Type)
[ Stock No?721 ]
- Surface Plate is Granite and Flatness is JISGrade 1
- The Stock moves up/down by gear
- Due to balance weight within the column, it moves with minimum force
*According to your requirement, we can manufacture head spin type
*Test bar is not included.
| Code No. |
Model |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Center Axis Perpendicularity (μm) |
Mass
(kg) |
|---|
| SVP201 |
VPG-1 |
600×500 |
400 |
150 |
Carbide MT-2 |
5 |
195 |
|---|
| SVP202 |
VPG-2 |
900×600 |
700 |
200 |
Carbide MT-3 |
8 |
400 |
|---|
| SVP203 |
VPG-3 |
1000×750 |
1000 |
240 |
12 |
510 |
|---|
| SVP204 |
VPG-1L |
750×500 |
370 |
200 |
Carbide MT-2 |
5 |
300 |
|---|
Vertical-TypeBench Centers (VP-Type)
[ Stock No?720 ]
- Surface Plate flatness is JIS Grade 1.
- Surface Plate is bag type, therefore long term accuracy can be manitained.
- The Stock moves up/down by gear.
- Due to balance weight within the column, it moves with minimum force.
*According to your requirement, we can manufacture head spin type.
*Test bar is not included.
| Code No. |
Model |
Measurement
(L×Wmm) |
Center Distance
(mm) |
Center Height
(mm) |
Use Center |
Center Axis Perpendicularity (μm) |
Mass
(kg) |
|---|
| SVP101 |
VP-1 |
600×500 |
400 |
150 |
Carbide MT-2 |
5 |
230 |
|---|
| SVP102 |
VP-2 |
900×600 |
700 |
200 |
Carbide MT-3 |
8 |
440 |
|---|
| SVP103 |
VP-3 |
1000×750 |
1000 |
240 |
12 |
550 |
|---|
| SVP104 |
VP-1L |
700×600 |
370 |
200 |
Carbide MT-2 |
5 |
250 |
|---|
Deflection Tester for Gear (SR-Type)
[ Stock No?304 ]
- For gear circle pitch deflection measurement
- Dial Gauge gripping chuck moves up/down due to rack gear.
- The probe easily moves up/down using the lever.
- 7 probes are supplied by default. (Module 1 to 4, 0.5 interval)
*Dial gauge and test bar are not included.
*We can manufacture special measurement probles according to your requirement.
| Code No. |
Model |
Full Lenght
(Lmm) |
Center Distance
(mm) |
Effective Center
Height (mm) |
Use Center |
Parallelism
(μm) |
Mass
(kg) |
|---|
| SR101 |
SR-1 |
640 |
300 |
200 |
Carbide MT-2 |
4 |
72 |
|---|
Attachment for Gear Deflection Measurement (SHH Type)
[ Stock No?101 ]
- For gear circle pitch deflection (Deflection) Measurement.
- Install and use with Standard Model tester, Rack Slide Type tester, etc.
- 7 probes are supplied by default. (Every 0.5 from Module 1 to 4)
*Dial Gauge and Deflection Tester are not supplied.
*We can manufacture special measurement probles according to your requirement.
| Code No. | Model | Applicable Deflection Tester | MAX Gear Diameter
(mm) | Probe (7 pcs)
(Module) | Mass
(kg) |
|---|
| SHH100 |
SHH-0 |
P-1,2,3 Type |
130 |
1.0 – 4.0
(0.5 increment) |
4 |
|---|
| SHH101 |
SHH-1 |
NO.-1 Type |
220 |
5 |
|---|
| SHH102 |
SHH-2 |
No.-2 Type |
380 |
10
|
|---|
Attachment for V Support with Rollers (SAR Type)
- Attachment used for measurement when adopting external diameter standard.
- Roller creates a V shape, making it difficult to dent the work piece contact surface.
- Work rotation is easy even for heavy work pieces and so high accuracy measurement can be performed.
- Supported work size φ40~φ100
*Dial Gauge, test bar and deflection tester are not provided. These have to arranged separately.
| Code No. | Model | Applicable Bench
Center | Roller Interval
Parallelism | Roller
Deflection | Mass
(kg) |
|---|
| SAR101 |
SAR-1 |
No.1 ML-1 |
0.01 |
0.003 |
4 |
|---|
| SAR102 |
SAR-2 |
No.2 ML-2 |
0.01 |
0.003 |
7 |
|---|
Attachment for V Support with Height Adjustment (SAV-Type)
- Attachment used for measurement when adopting external diameter standard
- In order for the support part to support various external diameters, the height of the V Support is adjustable on one side
- V Support width is designed to be narrow. It can also support both flangged type of work pieces.
- Supported work size φ8 ~ φ50
- Standard height adjustment range for the adjustable side is ±10
*Dial Gauge, test bar and deflection tester are not provided. These have to arranged separately.
| Code No. | Model | Applicable Bench
Center | Mass
(kg) |
|---|
| SAV101 |
SAV-1 |
No.1 ML-1 |
4 |
|---|
| SAV102 |
SAV-2 |
No.2 ML-2 |
7.5 |
|---|
Arm for Lever Type Dial Gauge (with Micromotion adjustment)?
For deflection testers, a stand that can utilize installation type dial gauge is supplied by default.
By exchanging the arm, it becomes possible to install a lever type dial gauge. Because it comes with a micromotion adjustment knob, dial gauge setting is easy.
*System installation hole is φ6mm (Dial Gauge is not included.)
| Code No. |
Applicable Bench
Center Model |
|---|
| SS101 |
No.1, ML-1 |
|---|
| SS102 |
No.2, ML-2 |
|---|
| SS103 |
No.3, ML-3 |
|---|
| SS104 |
P-1, P-2, P-3 |
|---|
|
| |
|
|
|
|
|
|
|
Sales Engineer 
098-4288648 
เก็บเป็นหน้าที่ใช้บ่อย
ตั้งเป็นหน้าแรก
