Model 205 Two Conductors, 4 Amps
|
|
|
High-speed model available (205-H) Low-torque/low-temp. models available (205-L) Available with stainless steel ball bearing (205-SS) |
Mercotac model 205 is ideal for two-wire applications, such as thermocouples, strain gages, eddy current test devices, and wind turbine blade sensors, due to its compact size, quality signal connection, low torque and low cost. Model 205 replaces the old model 590 for Leslie speakers and Hammond organs. |
|
|
Model No. |
Terminals |
Voltage AC/DC |
Amp Rating @240VAC |
Max. Freq. MHz |
Contact Resistance |
Max. RPM |
Temp Max. F (C) / Min. F (C) |
Rotation Torque (gm-cm) |
Circuit Separation |
205 |
2 |
0-250 |
4 |
200 |
<1m
|
|
|
2000 |
140 (60) /45(7) |
75 |
>25M
|
|
|
205-SS |
2 |
0-250 |
4 |
200 |
<1m
|
|
|
2000 |
140 (60) /45(7) |
75 |
>25M
|
|
|
205-L |
2 |
0-250 |
4 |
200 |
<1m
|
|
|
1200 |
140 (60) /-20(-29) |
20 |
>25M
|
|
|
205-LS |
2 |
0-250 |
4 |
200 |
<1m
|
|
|
1200 |
140 (60) /-20(-29) |
75 |
>25M
|
|
|
205-H |
2 |
0-250 |
4 |
200 |
<1m
|
|
|
3600 |
140 (60) /45(7) |
35 |
>25M
|
|
|
205-HS |
2 |
0-250 |
4 |
200 |
|
3600 |
140 (60) /45(7) |
35 |
>25M
|
|
|
"SS" designator indicates stainless steel ball bearing (recommended for wet or corrosive environments) "L" designator indicates low torque / low temp. "LS" designator indicates low temp. & stainless steel ball bearing "H" designator indicates high RPM "HS" designator indicates high RPM & stainless steel ball bearing
Model 205 Accessories |
|
Model 205 Connections |
Model 205 Suggested Mounting Methods |
Model 205 is typically mounted by the knurled metal receptacle, which is press-fit into the rotating member of the machine. When mounting horizontally, mount the Mercotac so the body of the connector rotates. |
|
Receptacle Mount Hole Dimensions
|
MODEL |
HOLE DIAMETER (Ø) * |
DEPTH |
591, 592, 594 |
.283" (7.19) |
.35" (8.89) |
*Inch (mm) Tolerance Ø |
+.001" (+.025) |
|
|
|
-.000" (-.000) |
|
|
|
|
Installation Notes:
- the up arrow should not point below horizontal
- do not solder to or bend connector tabs
- avoid lateral forces and mechanical loads (overly stiff or tight wires)
- do not rigid mount both ends of connector
- limit mounting eccentricity (runout / wobble) to .005" (.13mm)
- provide overload protection within the circuit
- avoid vibration and bumping motions
|
สนใจติดต่อขอรายละเอียดเพิ่มเติมได้ที่
บริษัท น่ำแซอินเตอร์เทรดดิ้ง จำกัด
Tel: 02-223-2271-3
Fax: 02-225-5546
E-mail: [email protected]
Website: www.namsae.com
Facebook: www.facebook.com/namsaefanpage
Line: @namsae
Instagram: namsae_official
|